Goodjob-Capture Software-operation progress
捕捉軟件的操作流程
1:CEL image capture 化學發光影像的捕捉
The system will automatic active the image capture program when booting.
系統啟動時，系統自動運行影像捕捉程序。
2:Quick user guide 快速使用指南
(1) choose Loop to start realtime image to show sample area and load chemi-membrance.
選擇“Loop”鍵，實時影像會顯示樣品面積和負載化學膜。
(2) Choose bin2 to speed up realtime image running. 選擇bin2，加快實時影像運行
PS: For chemi-sample pre-set parameter 備注：化學發光樣品預先參數設置
1) auto-stretch atuo-stretch（自動延伸）
2) negative negative(否定、負的)
(3) turn off the reflectant white light when start to capture image 當開始影像捕捉時，關閉反射白光
(4) change exp.time 改變曝光時間
(5) press Loop again to stop realtime image .press Time-lapse,set desire capture number
再次按“Loop”鍵停止實時取相。按“Time-lapse”(延時)，設置想要的捕捉圖片數量。
(6) choose directory to save capture images save as tif.must be key in this eaction is only first time use time-lapse. Routine use just press Next dir will auto save to new diretory.
選擇目錄，以tif.的后綴名保存照片。這一步在**次使用“Time lapse”時是非常關鍵的。常規應用就可以直接選擇“Next dir”(下級目錄)，系統會自動保存到新的地址。
PS:Must select “Autosave images”before capture. Otherwise the present directory will have no image.
備注：捕捉前必須選擇“Autosave images”，負責目前的目錄里不會存有圖像。
(7) start to capture image Time-lapse fuction. 開始用“Time-lapse”捕捉圖像。
(8) Under auto-stretch control in the beginning the display window will be high sensitive on weak bands and its image will be a little rough that depend on samples concentration.
在開始“auto-stretch”功能的作用下，窗口會出現高敏感度的弱信號條帶并且圖像有點粗糙，這都取決于樣品的濃度。
This is helpful for user to know whether weaks bands is there. It will show nice picture in the final images after more fluorescent signal collected.
這有助于使用者發現是否存有弱信號條帶。并且在收集更多熒光信號后，*后的成片效果會非常好。
Final images will display good signal intensity and have white and smooth background. This is because system has capture enough signal after Time-lapse choose final images as your best results.
*終成像會有好的信號強度和白色穩定的背景。這是因為“Time-lapse”，系統捕捉了足夠多的信號。選擇*后的圖像作為你*好的結果。
(9) Press reset to next time capture 選擇“Reset”（重設）開始下次捕捉
De-select Auto-save images when fininsh time-lapse
當 “time-lapse” 結束時，取消“Auto-save images”(自動保存圖像)
De-select Auto-stretch 取消“Atuo-stretch”
Set desire 設定期望值
Black no. 黑度
White no. 白度
Will show image intensity increase gradually. 圖像強度逐漸增加
(10) stop Loop. Start “Time lapse” 停止“Loop”。開始“Time-lapse”
(11) increase exp.start 增加曝光時間
During Time-lapse capture user can add any no. of imges or expand exp. Time before the last image reach. If you feel sample is too weak.You can stop any time.If you feel sample signal is too strong then just few images is enough.
在“Time-lapse”時，捕捉*后圖像前使用者都可以增加圖像數量或者改變曝光時間。如果你感覺樣品信號太弱，任何時間都可以停止。如果你感覺太強，少量幾張圖像就夠了。
Under non-auto-stretch control user can see sample signal increase one by one.this will look like X-ray film,but for quantitation user must take care which bands will easy to over expose and saturation.
沒有選擇“auto-stretch”功能的用戶可以觀察到樣品信號一張張增強。這看起來像X光片。但是對于定量用戶必須關心條帶是否易于曝光和飽和。
User can choose any one image to check results after Time-lapse finished .Just click time-lapse no.
“Time-lapse”后，用戶可以選擇任何一張圖像來核對結果。只需要點擊對應的圖像編碼。
(12) Separate a group of Stack to images into individual image. 從一堆圖像中分出一張獨立的照片。
(13) Choose “Windows” “Titles” to spread each images on deskTop.
選擇“window”-“Titles”，把每張照片放在桌面上。
(14) Collect all image into a stack file PS:“Stacks”- “imges to stack”-“name”
把所有的圖像放在一個圖像文件里。
(15) “Make montage”. PS:“Stacks”-“Make montage”
(16) Set scale factor 0.5* or 1* 設置“scale factor”（比例因子）0.5或0.1
(17) Quantitation: open one images 定量：打開一張圖像
Familiar with the data of chemi-image:Row data should be black background.white bands and intensity will be positive.Most of lab whould like to see the image like X-ray film.so the data will be negative.it need to be inverted when chemi-image what to quantitation.It will not need to inverted.If original image capture with setting at Non-Negative.
熟悉化學發光圖像的數據：并行數據應該是黑色背景。白色條帶和亮度較大。大多數的實驗室想觀察X光片，所以數據應該是Negative.當化學發光圖像要定量時，圖像需要反過來。如果原始圖像設置為Non-Negative，那么圖像不需要翻轉。
The follow image will see data is low when mouse on dark bands and data is high at white background.
當鼠標移動到黑色條帶時，圖像數據較低。白色條帶數據較高。
Background correct
Input optimum Rolling ball radius 設置*佳“Rolling ball radius”值
(18) Choose quantitative tool draw around the target bands. 用定量分析工具（Image J）圈定分析條帶
(19) Press“Analyze”“Measure”repeat for each bands. 選擇“Analyze”-“Measure”對每條條帶重復操作